联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
电动门安装
安装
install
（1）确定传达室内控制盒的位置,即操纵伸缩门开关的装置位置；
(1) Determine the position of the control box in the communication room, that is, the position of the device that operates the telescopic door switch;
（2）将220V电源引到控制盒的位置下端,要求最好是再带1根接地线,粗细规格为1.37,而且有漏电保护装置,并采用PVC暗敷；
(2) Lead 220V power supply to the lower end of the control box. It is better to have another grounding wire with a thickness of 1.37 and a leakage protection device, and use PVC concealed coating.
（3）预留￠32mm PVC管道,从控制盒的位置下端往下至地平面以下,穿墙往外,至轨道大致位置地平面下0.1-0.15米处,供以后伸缩门室外线路入室；
(3) Reserve 32mm PVC pipeline, from the lower end of the control box down to below the ground level, through the wall outside, to the track roughly 0.1-0.15m below the ground level, for later expansion doors and outdoor lines into the room;
（4）按照上表得出门洞长度，砌门洞时洞宽内净空不小于0.75-0.8米,高度内净尺寸普通门不小于门高+0.25米,豪华门不小于门高+0.1米;门洞末端里侧中上端留宽0.4米,高0.6米检修孔,有条件的可将门洞总长度再加长0.2-0.3米,这样可将检修孔改成一扇小门,方便日后检修维护伸缩门电气线路；
(4) According to the above table, we can get the length of the door, when we build the door, the clearance in the width of the hole is not less than 0.75-0.8 meters, the net size in the height of the ordinary door is not less than + 0.25 meters, and the luxury door is not less than + 0.1 meters; the middle and upper end of the end of the door is 0.4 meters wide and 0.6 meters high, and the total length of the door can be lengthened by 0.2-0.3 meters if conditions permit. The hole is changed into a small door to facilitate the maintenance of the electrical circuit of the telescopic door in the future.
（5）在铺设轨道前除留下约0.8-0.9米宽外,先做好两边的地面;2-3日(冬天5-7日)后,再在铺设轨道的同时,土建配合做好轨道处的地面，注意铺设轨道期间，路面禁止通行，以免压弯轨道；
(5) In addition to leaving about 0.8-0.9 meters wide before laying the track, the ground on both sides should be done well; after 2-3 days (5-7 winter), the ground at the track should be done well with civil construction. Pavement should be forbidden to pass during laying the track so as to avoid bending the track.
（6）安装伸缩门，接好线路，调试开关控制盒。
(6) Install the telescopic door, connect the circuit and debug the switch control box.
install
（1）确定传达室内控制盒的位置,即操纵伸缩门开关的装置位置；
(1) Determine the position of the control box in the communication room, that is, the position of the device that operates the telescopic door switch;
（2）将220V电源引到控制盒的位置下端,要求最好是再带1根接地线,粗细规格为1.37,而且有漏电保护装置,并采用PVC暗敷；
(2) Lead 220V power supply to the lower end of the control box. It is better to have another grounding wire with a thickness of 1.37 and a leakage protection device, and use PVC concealed coating.
（3）预留￠32mm PVC管道,从控制盒的位置下端往下至地平面以下,穿墙往外,至轨道大致位置地平面下0.1-0.15米处,供以后伸缩门室外线路入室；
(3) Reserve 32mm PVC pipeline, from the lower end of the control box down to below the ground level, through the wall outside, to the track roughly 0.1-0.15m below the ground level, for later expansion doors and outdoor lines into the room;
（4）按照上表得出门洞长度，砌门洞时洞宽内净空不小于0.75-0.8米,高度内净尺寸普通门不小于门高+0.25米,豪华门不小于门高+0.1米;门洞末端里侧中上端留宽0.4米,高0.6米检修孔,有条件的可将门洞总长度再加长0.2-0.3米,这样可将检修孔改成一扇小门,方便日后检修维护伸缩门电气线路；
(4) According to the above table, we can get the length of the door, when we build the door, the clearance in the width of the hole is not less than 0.75-0.8 meters, the net size in the height of the ordinary door is not less than + 0.25 meters, and the luxury door is not less than + 0.1 meters; the middle and upper end of the end of the door is 0.4 meters wide and 0.6 meters high, and the total length of the door can be lengthened by 0.2-0.3 meters if conditions permit. The hole is changed into a small door to facilitate the maintenance of the electrical circuit of the telescopic door in the future.
（5）在铺设轨道前除留下约0.8-0.9米宽外,先做好两边的地面;2-3日(冬天5-7日)后,再在铺设轨道的同时,土建配合做好轨道处的地面，注意铺设轨道期间，路面禁止通行，以免压弯轨道；
(5) In addition to leaving about 0.8-0.9 meters wide before laying the track, the ground on both sides should be done well; after 2-3 days (5-7 winter), the ground at the track should be done well with civil construction. Pavement should be forbidden to pass during laying the track so as to avoid bending the track.
（6）安装伸缩门，接好线路，调试开关控制盒。
(6) Install the telescopic door, connect the circuit and debug the switch control box.
